12 _____________________________________________________________________________________
Single-Port, 40W, IEEE 802.3af/802.3at PSE
Controller with Integrated MOSFET
Pin Description (continued)
PIN
NAME
FUNCTION
13
LEGACY
Legacy Detection Logic Input. Referenced to V
EE
. LEGACY is internally pulled up to the digital
supply. Leave unconnected to activate the legacy PD detection. Force low to disable this function.
The LEGACY logic level latches after the device is powered up or after a reset condition.
14
EN
Enable Input. Referenced to V
EE
. EN is internally pulled up to the digital supply. Leave uncon-
nected to enable the device. Force low for at least 40Fs to reset the device. The MIDSPAN, OSC,
and LEGACY states latch-in when the reset condition is removed (low-to-high transition).
16, 18, 20,
22, 24, 28
N.C.
No Connection. Not internally connected. Leave N.C. unconnected.
17
LED
LED Indicator Open-Drain Output. Referenced to V
EE
. LED can sink 10mA and can drive an exter-
nal LED directly. Blinking functionality is provided to signal different conditions (see the PWM and
LED Signals section). Connect LED to AGND externally (see Figures 6 and 7) or to an external
supply (if available) through a series resistance.
19
OSC
AC-Disconnect Triangular Wave Output. Bypass with a 100nF (Q10% tolerance) external capacitor
to V
EE
to enable the AC disconnect function. Connect OSC to V
EE
to disable the AC disconnect
function and to activate the DC disconnect function. The OSC state latches after the device is
powered up or after a reset condition.
21
AGND
High-Side Supply Input
23
DET
Detection/Classification Voltage Output. DET is used to set the detection mark event and clas-
sification probe voltages and for the AC current sensing when using the AC disconnect function.
To use the AC disconnect function, place a 1kI and 0.47FF RC series in parallel with the external
protection diode to OUTP (see Figure 7).
25
OUTP
Port Pullup Output. OUTP is used to pull up the port voltage to AGND when needed. If AC discon-
nect is used, connect OUTP to the anode of the AC-blocking diode. If AC disconnect is not used,
connect OUTP to OUT (see Figures 6 and 8). Bypass OUTP to AGND with a 100V, 0.1FF ceramic
capacitor.
26, 27
OUT
Integrated MOSFET Output. If DC disconnect is used, connect the port output to OUTP (see
Figures 6 and 8). If the AC disconnect function is used, connect OUT to the cathode of the
AC-blocking diode (see Figure 7).
EP
Exposed Pad. Connect EP to V
EE
externally. See the Layout Procedure section for details.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX5972AETE+T
IC CONTROLLER INTERFACE 16TQFN
MAX5978ETJ+
IC CTLR HOT-SWAP 32TQFN
MAX5981BETE+
IC CTRLR PD IEEE 802.3AF 16TQFN
MAX5986AETE+
IC POE SWITCH PSE 16TQFN
MAX6509CAZK/V+T
IC TEMP SWITCH RES-PROG 5TSOT
MAX6513TT075+T
IC TEMP SWITCH REMOTE 6-TDFN
MAX6581TG9A+
IC TEMP SENSOR 8-CH PREC 24-TQFN
MAX6602UE9A+T
IC TEMP MONITOR 5CH 16-TSSOP
相关代理商/技术参数
MAX5971AETI+T
功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5971AETI+W
制造商:Maxim Integrated Products 功能描述:IEEE802.3 AT PSE SWITCH - Rail/Tube
MAX5971AEVKIT
功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
MAX5971AEVKIT+
制造商:Maxim Integrated Products 功能描述:PD INTERFACE CONTROLLER - Boxed Product (Development Kits)
MAX5971BETI
制造商:Maxim Integrated Products 功能描述:
MAX5971BETI+
功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5971BETI+T
功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5971BETI+W
制造商:Maxim Integrated Products 功能描述:SINGLE-PORT, 40W, IEEE 802.3AF/AT, PSE CONTROLLER WITH IC - Rail/Tube